PCA GT2, GT3 and Cup Car SIG

PCA GT2, GT3 and Cup Car SIG (http://gt2gt3cup.org/index.php)
-   GT2, GT3, RS and Cup Car Discussions (http://gt2gt3cup.org/forumdisplay.php?f=2)
-   -   Center Lock Wheels (http://gt2gt3cup.org/showthread.php?t=177)

stujelly 05-01-2011 11:04 PM

Center Lock Wheels
 
I have read so many threads about people complaining about the center lock wheels, what a pain they are, that I have been postponing doing my own wheel swap and brake inspection.

This weekend I pull my wheels off my 11 GT3 RS for the first time. I believe I followed the right procedure by leaving the car in the air while I torqued each wheel to the new track spec of 444 ft lbs. I used the truck brake pedal tool and it was a one man job. Probably took 30 to 40 minutes because I took my time and did one wheel at a time. There was adequate grease on the hub. I made sure the wheel was seated against the hub before torquing in the air. I used the mac tools 4 to 1 torque multiplier and a regular mac tools torque wrench set at 120 lbs because the multiplier info states there could be a 10% to 20% variation.

It was a no brainer. What did I miss?

I do have one question, what jack are most of you using? My car is set at the euro ride height with 18 inch GMG wheels so it sits a bit low and it was a strain to lift the car to slip the jack underneath it, again, one man show.

BTW I love this new forum.

Thanks guys

FTS 05-01-2011 11:17 PM

Re: Center Lock Wheels
 
Quote:

Originally Posted by stujelly (Post 1218)
BTW I love this new forum.

Thanks guys

This means a lot coming from one of our members, thank you!

As for the jack, I use regular $100 small, light jack sold at every store, but my car is not as low as yours most likely, and it fits with only 5-10 mm clearance. I would imagine you may need to use some wood pieces to put the car one first, or race pads to roll onto first.

On the question of "what did I miss?" Just because you don't mention it:
  • making sure the center lock gears are flush with the wheel center gears.
  • Once you torque the wheels while they are in the air, for tracking purposes, you should do the follow up: bring the car onto the floor, slightly loosen the nut, then retorque to spec.

mooty 05-02-2011 12:51 AM

Re: Center Lock Wheels
 
jack: ac hydraulic

usually wheel change is not hard. but if you do it 3x a day trying to maximum tire performance, it's too slow b/c it does'nt allow u to use impact gun.

jenk12m 05-02-2011 06:58 PM

Re: Center Lock Wheels
 
Tire rack low profile. Works great

TRAKCAR 05-02-2011 07:19 PM

Re: Center Lock Wheels
 
You mean this one?
http://www.tirerack.com/accessories/detail.jsp?ID=67

It does not say low profile? is 3.5" low enough for our cars?

Izzone 05-03-2011 06:01 PM

Re: Center Lock Wheels
 
I am looking for a aluminum jack for car......have AC for garage

Any reccomendations I will buy it now

Nice but expensive

http://www.asedeals.com/zinko_alumin...ing_jacks.html

Centerlock is no big deal, just different

stujelly 05-03-2011 06:31 PM

Re: Center Lock Wheels
 
Quote:

Originally Posted by Izzone (Post 1286)
I am looking for a aluminum jack for car......have AC for garage

Any reccomendations I will buy it now

Nice but expensive

http://www.asedeals.com/zinko_alumin...ing_jacks.html

Centerlock is no big deal, just different

Wow those are nice but pricey. I have a nice craftsman that I think is about 3 inches in height for about 200 bucks. That extra 3/4 inch lower would work great. I think I will look into that and then put the craftsman in the trailer.

Again thanks for the great info.

FTS 05-03-2011 07:48 PM

Re: Center Lock Wheels
 
Woww, one of the most expensive ones I have seen thus far. But think about it, I use my jacks on average 6-8 years, so yearly cost is minimal. Would I pay it then? Nope :)

ATL Fahrer 05-04-2011 06:15 AM

Re: Center Lock Wheels
 
Bought this one http://www.northerntool.com/shop/too...3500_200313500

Cheap and goes down to 3.25"


All times are GMT -5. The time now is 07:16 PM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.

Garage vBulletin Plugins by Drive Thru Online, Inc.

©2010-2018, Porsche Club of America. This site is owned & operated by the Porsche Club of America, and is not affiliated in any way with Porsche AG or Porsche Cars North America.