Go Back   PCA GT2, GT3 and Cup Car SIG Forums > GT2/GT3/Cup Car Register Discussions > GT2, GT3, RS and Cup Car Discussions
Register Forums FAQs Search

GT2, GT3, RS and Cup Car Discussions Discussions on all topics related to all Porsche GT vehicles

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 04-24-2011, 10:24 AM
Trackrat's Avatar
Trackrat Trackrat is offline
Vice Advocate
 
Join Date: Feb 2011
Posts: 179
Downloads: 0
Uploads: 0
Default MovIt Carbon Silicon Carbide Rotors as PCCB Replacement?

I have been working with MovIt for eight months now on a PCCB replacement brake system for my Boxster Spyder and GT3RS/GT2RS. 2RS and 3RS share identical rotors/hats/calipers/pads. The OE PCCB rotors as most of you know will die an expensive death when vigorously tracked more than 10-15 times.

The Spyder system (calipers/braided lines/rotors) was installed in December and so far with street driving has been rock solid. The GT3RS system development has dragged on interminably but as a stop-gap MovIt provided me with a set of GenII CSC rotors to expiriment with and hammer on.

I installed the MovIt rotors on the 2RS and this week was able to put two track days on them and I showed no mercy when braking. Compared to OE PCCB, the pedal was rock solid even under the most severe braking conditions (repeated high speed threshold braking). Modulation with the MovIt's was much improved vs the PCCB.

The nice thing is they bite well when cold or hot. P50 Greens are dangerous to run on the street and take 2-3 laps to warm up and bite well. OE P40's on a OE system are a bit hard to modulate when cold and I can make them fade a bit when very hot.

The MovIt CSC's had consistent bite hot or cold.

While two days is not much, it was a 620hp car and the MovIt's so far look look pristine. Weight difference vs PCCB is .7lb greater per rotor, or + 2.79 lbs for all four. A weight trade-off I am more than happy to make for rotors that have a claimed lifetime of essentially forever.

I will update this thread as my testing progresses. So far, I am very happy with them. In the USA MovIt brakes are distributed by Tom Frederico email:Tom@TFEnt.com

As I understand it, rotor replacements are available now but the full system for GT3 is still in development. Billet calipers will eliminate the bevel pad wear we all know an hate and also result in a firmer pedal under severe conditions.

MovIt main website: http://www.movitbrakes.com/en/produkte/keramikbremsen/

Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.
Attached Files
File Type: pdf MOV_IT-CER english.pdf (93.9 KB, 10 views)

Last edited by Trackrat; 07-07-2011 at 01:31 PM.
Reply With Quote
  #2  
Old 04-24-2011, 10:31 AM
bman's Avatar
bman bman is offline
Registered Porsche Owner
 
Join Date: Feb 2011
Posts: 146
Downloads: 0
Uploads: 0
Default Re: MovIt Carbon Silicon Carbide Rotors as PCCB Replacement?

Subscribed! Thanks for the write up.

What type of pad are you running?
Reply With Quote
  #3  
Old 04-24-2011, 10:42 AM
TRAKCAR's Avatar
TRAKCAR TRAKCAR is offline
Vice Advocate
 
Join Date: Feb 2011
Posts: 359
Downloads: 0
Uploads: 0
Garage
Default Re: MovIt Carbon Silicon Carbide Rotors as PCCB Replacement?

+1 Please keep posting!!

Thank you so much for being the tester.

Bman, nice meeting you at VIR!

The oem steel rotors are $550.00 front and $500.00 rear. Lasting 20 days max.
Pagid pads are $750.00. Lasting 10 days max.

I will try some diffrent pads/steel in the meanwhile and start a seperate thread to accurately compare running cost VS quality of brake feel. Even some crazy expensive brake pads from Endless if I can get them.

PCCB users have different math and it will pay off even sooner for them, but I am very interested as well and as you keep posting we will learn how quickly the Movit brake system will pay off in saved pads and rotors, as well as the labour saved.
__________________
Peter National PCA Instructor.
Pics and youtubes ==> Daily driver '10RS white/gold. White OEM RS roll bar, red schroth seat belts, CUP LSD, lip and Gurney, Sharky, V1, K40 laser blocker.

Sold '07GT3 white
Reply With Quote
  #4  
Old 04-24-2011, 11:14 AM
Trackrat's Avatar
Trackrat Trackrat is offline
Vice Advocate
 
Join Date: Feb 2011
Posts: 179
Downloads: 0
Uploads: 0
Default Re: MovIt Carbon Silicon Carbide Rotors as PCCB Replacement?

Quote:
Originally Posted by bman View Post
Subscribed! Thanks for the write up.

What type of pad are you running?
When using just OE replacement rotors (not calipers or oversize kits) then MovIt suggests the OE P40 pads. I will do a tear down tomorrow and will update the thread with pad wear characteristics.

Quote:
Originally Posted by TRAKCAR View Post
+1 Please keep posting!!

Thank you so much for being the tester.

PCCB users have different math and it will pay off even sooner for them, but I am very interested as well and as you keep posting we will learn how quickly the Movit brake system will pay off in saved pads and rotors, as well as the labour saved.
You got it Peter. Yes, the value proposition for the MovIt system involves some big number$ so is a bit of a challenge to wrap your head around, but boils down to:

Lifetime rotors, or even transfer to your next car (!).
Reduced pad wear (we shall see).
Preserving reduced rotating mass/lowered unsprung weight.
When billet caliper is installed no more pad flipping/beveled pads (we shall see).
Greatly improved pedal feel, increased ability to modulate.
Reply With Quote
  #5  
Old 04-24-2011, 11:00 PM
TRAKCAR's Avatar
TRAKCAR TRAKCAR is offline
Vice Advocate
 
Join Date: Feb 2011
Posts: 359
Downloads: 0
Uploads: 0
Garage
Default Re: MovIt Carbon Silicon Carbide Rotors as PCCB Replacement?

Hopefully the pads last better too. No more rotors! A thou here, a thou there and pretty soon you're talking real money ;-)
__________________
Peter National PCA Instructor.
Pics and youtubes ==> Daily driver '10RS white/gold. White OEM RS roll bar, red schroth seat belts, CUP LSD, lip and Gurney, Sharky, V1, K40 laser blocker.

Sold '07GT3 white
Reply With Quote
  #6  
Old 04-25-2011, 12:06 AM
PJS's Avatar
PJS PJS is offline
Registered Porsche Owner
 
Join Date: Apr 2011
Location: Seattle
Posts: 42
Downloads: 0
Uploads: 0
Default Re: MovIt Carbon Silicon Carbide Rotors as PCCB Replacement?

subscribed - you are my test bed
thank you for sticking your neck out and posting about it
Reply With Quote
  #7  
Old 04-25-2011, 11:01 AM
stujelly's Avatar
stujelly stujelly is offline
Registered Porsche Owner
 
Join Date: Apr 2011
Posts: 45
Downloads: 0
Uploads: 0
Default Re: MovIt Carbon Silicon Carbide Rotors as PCCB Replacement?

I am on board with this too, as I was just getting ready to purchase the OEM steel replacements for my 3RS.

Cant wait to hear more.
Reply With Quote
  #8  
Old 04-25-2011, 09:44 PM
Trackrat's Avatar
Trackrat Trackrat is offline
Vice Advocate
 
Join Date: Feb 2011
Posts: 179
Downloads: 0
Uploads: 0
Default Re: MovIt Carbon Silicon Carbide Rotors as PCCB Replacement?

I swapped the rotors and pads from the 2RS to the 3RS today. Front pads are wearing beveled on leading edge but I expected that as MovIt has not yet supplied me with the calipers which should eliminate this.

Rear pads looked really good, no bevel and even wear side to side which does surprise me as I know PSM was working a lot.

The rotors looked pristine and like new. The original crosshatch pattern is still on them, and trust me when I tell you I hammered them with no mercy.

Pads, the OE P40's, looked about as always. So my initial impression of using rotors only, as an OE replacement, in the stock sizing, appears as though it might make sense. Three more days to hammer them again on the 3RS at a PCA event Fri/Sat/Sun. Will report back.

Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.

Last edited by Trackrat; 04-25-2011 at 10:22 PM.
Reply With Quote
  #9  
Old 04-26-2011, 07:17 AM
landjet's Avatar
landjet landjet is offline
Registered Porsche Owner
 
Join Date: Apr 2011
Posts: 60
Downloads: 0
Uploads: 0
Default Re: MovIt Carbon Silicon Carbide Rotors as PCCB Replacement?

It will be interesting to see if the claims made in the PDF prove true. Do these fit the stock GT3 6 piston calipers? If you don't mind me asking, what do these rotors cost per corner?
Reply With Quote
  #10  
Old 04-27-2011, 05:44 PM
Trackrat's Avatar
Trackrat Trackrat is offline
Vice Advocate
 
Join Date: Feb 2011
Posts: 179
Downloads: 0
Uploads: 0
Default Re: MovIt Carbon Silicon Carbide Rotors as PCCB Replacement?

Quote:
Originally Posted by landjet View Post
It will be interesting to see if the claims made in the PDF prove true. Do these fit the stock GT3 6 piston calipers? If you don't mind me asking, what do these rotors cost per corner?
Hi Landjet- I agree as to validity of the claims and I will update this thread as real -life experience plays out. So far...so good. My direct replacement rotor solution only required me to swap out the hats which is tedious but not hard. I think MovIt offers a hat and rotor solution but of course you have to pay for that.

So far the difference in modulation and pedal feel are all for the good. More data on wear next week

I have to refer any pricing questions to your local distributor (Tom Frederico in USA).
Reply With Quote
  #11  
Old 04-27-2011, 05:48 PM
Trackrat's Avatar
Trackrat Trackrat is offline
Vice Advocate
 
Join Date: Feb 2011
Posts: 179
Downloads: 0
Uploads: 0
Default Re: MovIt Carbon Silicon Carbide Rotors as PCCB Replacement?

Quote:
Originally Posted by TRAKCAR View Post
Hopefully the pads last better too. No more rotors! A thou here, a thou there and pretty soon you're talking real money ;-)
So far front pad wear appears same as always, rear pad wear is much improved. But this is only with rotor change and not calipers and MovIt specific pads.

Quote:
Originally Posted by PJS View Post
subscribed - you are my test bed
thank you for sticking your neck out and posting about it
You are welcome! Lol...let me tell you my neck has some gashes on it! Whew.

Quote:
Originally Posted by stujelly View Post
I am on board with this too, as I was just getting ready to purchase the OEM steel replacements for my 3RS.

Cant wait to hear more.
Stay tuned...
Reply With Quote
  #12  
Old 04-28-2011, 02:15 PM
TRAKCAR's Avatar
TRAKCAR TRAKCAR is offline
Vice Advocate
 
Join Date: Feb 2011
Posts: 359
Downloads: 0
Uploads: 0
Garage
Default Re: MovIt Carbon Silicon Carbide Rotors as PCCB Replacement?

So, do they make the rotors just for the front that we could plop on the car witrh the staal calipers?
__________________
Peter National PCA Instructor.
Pics and youtubes ==> Daily driver '10RS white/gold. White OEM RS roll bar, red schroth seat belts, CUP LSD, lip and Gurney, Sharky, V1, K40 laser blocker.

Sold '07GT3 white
Reply With Quote
  #13  
Old 04-28-2011, 06:12 PM
NickW's Avatar
NickW NickW is offline
Registered Porsche Owner
 
Join Date: Apr 2011
Location: Chicago, Orlando, Vail, Hong Kong
Posts: 41
Downloads: 0
Uploads: 0
Garage
Default Re: MovIt Carbon Silicon Carbide Rotors as PCCB Replacement?

Can I assume these fit the 997 GT2 also?
Reply With Quote
  #14  
Old 04-28-2011, 08:25 PM
Izzone's Avatar
Izzone Izzone is offline
Registered Porsche Owner
 
Join Date: Apr 2011
Posts: 62
Downloads: 0
Uploads: 0
Default Re: MovIt Carbon Silicon Carbide Rotors as PCCB Replacement?

Quote:
Originally Posted by TRAKCAR View Post
So, do they make the rotors just for the front that we could plop on the car witrh the staal calipers?
I like where u are going

Endless makes pccb specific pads, wonder if they work with this
__________________
Randy - 997.2 GT3RS
Reply With Quote
  #15  
Old 04-28-2011, 10:46 PM
Trackrat's Avatar
Trackrat Trackrat is offline
Vice Advocate
 
Join Date: Feb 2011
Posts: 179
Downloads: 0
Uploads: 0
Default Re: MovIt Carbon Silicon Carbide Rotors as PCCB Replacement?

In the USA, Tom Frederico would be able to best advise on specific fitment but I know of no reason it wouldn't work?

Forewarned! A "lifetime" rotor is not cheap! And MovIt is right now taking forever to fill orders. Be prepared for a long delay and be happily surprised if not.
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -5. The time now is 06:06 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Garage vBulletin Plugins by Drive Thru Online, Inc.
©2010-2018, Porsche Club of America. This site is owned & operated by the Porsche Club of America, and is not affiliated in any way with Porsche AG or Porsche Cars North America.