MovIt Carbon Silicon Carbide Rotors as PCCB Replacement?

[Gator Bite]

Can someone provide a ballpark price for a set? Or is that some kind of secret?

Was this evaluation set provided to you at no cost or reduced cost?

Since the factory PCCB discs seem to hold up OK until 10 or 15 track days, I'd say that the jury is still out on the longevity of these. I will certainly watch closely and hope the claims prove to be true.

I don't understand why a billet caliper would prevent tappered pad wear. Can you provide more info?

[Trackrat]

Originally Posted by Gator Bite

Can someone provide a ballpark price for a set? Or is that some kind of secret?

Was this evaluation set provided to you at no cost or reduced cost?

Since the factory PCCB discs seem to hold up OK until 10 or 15 track days, I'd say that the jury is still out on the longevity of these. I will certainly watch closely and hope the claims prove to be true.

I don't understand why a billet caliper would prevent tappered pad wear. Can you provide more info?

Hi Gator Bite- Price is going to vary based on exchange rate (Euro) and options (specific application, friction ring size, w or w/o hats, etc). There are more variables than one might think. The way to get a quote is to contact the USA MovIt rep: Tom@tfent.com. No secrets, I am sure he will be happy to help you (accurately) price a set. I have no financial interest or benefits from any sales he makes.

The pictured discs were provided to me not for evaluation purposes (however I used the opportunity to make that my personal mission ) but as a "loaner" set of friction discs because my full system (I paid full price) was much delayed due to a variety of reasons. I thought it was a strong customer service gesture for them to do that. When my full system arrives, then it's my option to return or buy these loaners.

Based on my experience with the now dead PCCB discs (pics somewhere online but I will post them again to this thread) on my Spyder and GT3RS there is no doubt whatsoever in my mind the Movit discs are proving to be light-years ahead in wear characteristics under track use condition.

There are a wide variety of posts, over the years, on RL and 6Speed (easily searchable) regarding the tapered pad wear issue. General consensus is that the caliper is not rigid enough and flexes under track use conditions.

According to MovIt literature:

"MOVIT calipers with its 6-piston BILLET design, have bigger pistons (13 sets of custom designed configurations based on application), longer pads (108 cm²), are BILLET CNC machined from the highest strength 7075 aluminum and are T6 heat treated.

The caliper is much stronger than others and will not loose its strength even under high temperatures like cast calipers. The aluminum which is used in cast calipers (alsi5 or alsi7) has a strength factor of approximately 31,915.4-34,816.8 PSI. With an additional heat treatment this strength can be raised to approximately 42,070.3 PSI. The reason why most manufacturers use heat treated aluminum is simply the price. The material used for each "MOV’IT BILLET-CALIPER" has a strength factor of approximately 79,788.5- 82,689.9 PSI. So, the possibility to expand under growing pressure and heat is totally eliminated. CNC machined calipers need less space than cast calipers that can be used with a bigger disc under the same rim then the cast calipers. The material and the extremely strong and "wide" design of the "MOV’IT BILLET-Calipers" means the pressure to the pad is applied evenly even under extreme pressure, greater then 21,754.5 PSI. The heat is transferred to the maximum possible surface area, the temperature stays lower and the durability of all parts is higher. Cast calipers do not compress the pads evenly to the rotor when they expand under higher pressure or temperature. So, the rotor is not evenly heated and the pads wear faster and unevenly. A loss of the already lower braking force of cast calipers"

I do have a full MovIt system on my Spyder now since December: http://forums.rennlist.com/rennforum...-insanity.html which I paid full price for. After approx 7 hours of tracking, it is proof to me that MovIt offers a high-priced but even more high-value solution to those of us seeking a "lifetime" brake system for which we don't have to buy rotors ever again or flip pads after every 2 track days. There is no noticeable pad wear nor is the paint on the pads even discolored! (pics attached) That performance is hard to argue with.

It won't be a solution for everyone, or even most, as the value proposition can be a challenge to wrap one's head around. But it is there and it is quite compelling for those who have researched the current OE and aftermarket offerings and found them unsatisfying.

Folks who have read me over the years on RL/6Speed/TeamSpeed/RennTeam 2.0, and know me in person are aware I am an early adopter, and experiment with outside the box solutions. And then I post what my experiences are. Some are good, some not so much. To those who are not aware of my background and history might think I am a guerrilla marketer, but the truth is I am a "free-marketer" and a manufacturers greatest advocate or worst enemy. My efforts (100% voluntary and unpaid) on building gt2gt3cup.org are recent proof of that claim

Your questions are good and appropriate and if I can expand on anything I am happy to do so, just ask!

Spyder w/MovIt full system:



Seven hours of hard track time. No pad discoloration, rotors look new, no noticeable pad wear.

[Gator Bite]

Good stuff. I don't mean to accuse you of 'guerrilla marketing'. I just want to understand all the dynamics.

I'm not sure I totally buy the whole theory on tapered pad wear. If it were caused by a structural weakness in the caliper and it flexing, wouldn't the pads wear in a curve, less wear in the middle of the pad, more on each end where the caliper is clearly stronger because that's where the front and back are connected?

I would expect tapered wear on any large surface area brake pad that is mounted in a multi piston caliper. On any brake pad, there is going to be a certain amount of torque applied to the pad during braking. What will a motorcycle do if it brakes too hard? It will flip forward because of that torque. That torque is normal.

When we have a multi piston caliper, like the 6 piston units on your car, the pistons can move independently from one another, which allows the torque to turn the pad over time and wear the pad unevenly. Now the best way to compensate for this is to stagger the piston size with smaller pistons close to the leading edge and larger pistons closer to the trailing edge. I know Porsche does this on my 4 piston unit, I'm guessing they do the same on the 6 piston unit. But apparently they haven't staggered the sizes enough.

If the MovIt calipers stagger the pistons differently, this may have an effect on the tapered pad wear.

[FTS]

Originally Posted by Gator Bite

If it were caused by a structural weakness in the caliper and it flexing, wouldn't the pads wear in a curve, less wear in the middle of the pad, more on each end where the caliper is clearly stronger because that's where the front and back are connected?

I would expect tapered wear on any large surface area brake pad that is mounted in a multi piston caliper. On any brake pad, there is going to be a certain amount of torque applied to the pad during braking. What will a motorcycle do if it brakes too hard? It will flip forward because of that torque. That torque is normal.

When we have a multi piston caliper, like the 6 piston units on your car, the pistons can move independently from one another, which allows the torque to turn the pad over time and wear the pad unevenly. Now the best way to compensate for this is to stagger the piston size with smaller pistons close to the leading edge and larger pistons closer to the trailing edge. I know Porsche does this on my 4 piston unit, I'm guessing they do the same on the 6 piston unit. But apparently they haven't staggered the sizes enough.

Well not necessarily. The caliper shape, its metallurgical construct, piston design, all play a significant role in how heat is spread across the caliper and dissipated. Few years ago, Racecar Engineering mag pushed some technical articles from PFC on their NASCAR calipers and how the new Z-rated designs were making noticeable performance differences. I could not locate the article on their web site, but the following thesis is a very close approximation of what PFC was claiming:

http://soar.wichita.edu/dspace/bitst...pdf?sequence=1

I find Pete's adventures in testing "stuff" to satisfy his curiosity quite interesting, I really appreciate you taking the leading on finding and using these rare products Pete, thanks

[Trackrat]

Five hard track day follow-up. I set the second fastest time at the GG PCA TT with these rotors on the car. Much of the original honing marks still remain on the rotors. No obvious sign of wear.

LF



LR



RR

[stujelly]

I spoke with Tom yesterday. What a great guy and the statistics that he has for the long lasting performance of the rotor and pads is just mind blowing.

[Trackrat]

Originally Posted by stujelly

I spoke with Tom yesterday. What a great guy and the statistics that he has for the long lasting performance of the rotor and pads is just mind blowing.

The holy grail is a long lasting, track usable rotor with good modulation characteristics. The next two months will tell the tale and so far so good. These seem tough as nails.

Can't wait to install the full kit with the billet calipers- MovIt are you reading this??

[TRAKCAR]

Wow, that's impressive for 5 days of wear.

Besides the pallet of tightly wrapped $100.00 bills they want for them, do you think they can be driven (COLD!!) on the street?
It would suck to drive over the mail man because you can't stop the car driving down the driveway..

[Trackrat]

Originally Posted by TRAKCAR

Wow, that's impressive for 5 days of wear.

Besides the pallet of tightly wrapped $100.00 bills they want for them, do you think they can be driven (COLD!!) on the street?
It would suck to drive over the mail man because you can't stop the car driving down the driveway..

Haha

Unlike driving on the street with P50 Greens these use the P40 pad so cold and or wet stopping is no different from hot.

Your question is spot on and the good news is they work just fine when cold.

[TRAKCAR]

Cool :thumbup: How are the pads lasting? Same as before still?

[Trackrat]

Originally Posted by TRAKCAR

Cool :thumbup: How are the pads lasting? Same as before still?

Yes, pretty much. I am getting 5 hard track days on fronts and rears with PSM on all the time.

As caliper is OE, still getting beveled fronts and rears but to a lesser extent.

[TRAKCAR]

Beveling 100% due to calipers then, I assume.

[lightweight]

According to Tom: once one is able to use MovIt pads there is a considerable increase in pad lifespan. 2 years of 20 days/year tracking currently being seen by a customer. Could be 3 years with light track use. And never needing to switch pads between track and street. This is sounding more and more interesting.

[NickW]

Tracker- sorry to be a pain, but are these direct OE sized replacements for both front/rear? Can you PM me the MSRP when you get the chance, I am quite interested in them.

[Trackrat]

MovIt brake update: Things have taken a turn for the worse with delays in the supply of another kit, lack of follow-through on parts and other severe "miscommunications" (I am trying to say it nicely) and I currently CANNOT recommend anyone to purchase any MovIt parts. Email or IM me for current situation if you are thinking of giving them any business.